Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

Park Tool Adjustable Torque Driver
$78.00
Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.
Park Tool Bottom Bracket Tool - Campagnolo
$10.95
The BBT-4 is made for the installation and removal of 6-notch SC-S and AC-H cartridge cups used on sealed cartridge bottom brackets. These bottom brackets have six notches around the outside of each cup. The handle of the BBT-4 is vinyl coated for comfort. The major diameter of the tool is nominally 44mm, and the minor diameter 38mm. The BBT-4 is compatible with the following sealed cartridge bottom brackets: • Campagnolo Veloce • Xenon • Mirage • Daytona • Avanti
Park Tool Bottom Bracket/Cassette Tool (Campagnolo)
$8.95
Park's Bottom Bracket/Cassette Tool for Campagnolo is an indispensable tool for your Campagnolo drivetrain. It's for installing and removing all Record, Chorus, Centaur and Athena bottom brackets, and all Campagnolo cassette lockrings.
Park Tool CM-5.3 Cyclone Chain Scrubber
$28.99
Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent
Park Tool CT-3.3 Chain Tool
$45.99
A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP). *The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets. - Comfortable T-handle - Replaceable driving pin (CTP) - Investment cast steel body - Adjustable locating shelf
Park Tool Cassette Lockring Tool with 5mm Guide Pin
$9.49
Heat treated alloy tool steel, one inch base fits wrench or bench vise. Thin wall construction allows use without removal of cones and locknuts. The FR-5.2G has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, SunRace, SunTour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also Fits Shimano disc brake lockrings - Guide pin stabilizes tool
Park Tool Chain-Wear Indicator
$10.99
A worn chain shifts poorly and wears sprockets at an accelerated rate. Park Tool's Chain-Wear Indicator is a “go-no go” gauge designed to accurately indicate when a chain reaches .5% and .75%, the points at which most chain manufacturers suggest replacement. The updated CC-3.2 is longer, more accurate and features permanent measurement markings.
Park Tool Double-Ended Cone Wrench
$5.95
Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
Park Tool FR-3 Freewheel Remover
$13.49
The Park FR-3 Freewheel Remover fits SunTour four-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.
Park Tool FR-4 Freewheel Remover
$7.95
The Park FR-4 Freewheel Remover fits Atom, Regina, splined Zeus and some Schwinn-approved freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.
Park Tool Freewheel Remover
$8.49
12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.
Park Tool Hex Wrench Set (4, 5, 6 mm)
$11.49
The AWS-1 is one of Park's most-popular tools because it fits the most-turned bicycle bolts. It features 4, 5, and 6mm Allen wrenches in a Y shape for excellent leverage. Each Allen is vinyl coated for comfort.
Park Tool Home Mechanic Starter Kit
$144.99
A great way to start a tool collection! The perfect combination of tools to help the novice home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-3 includes more than 15 genuine Park Tool products plus a custom Park Tool toolbox. The SK-3 includes: AWS-11 Fold-Up Hex Wrench Set CC-3.2 Chain Checker CN-10 Professional Cable and Housing Cutter CT-5 Mini ChainBrute Chain Tool GP-2 Pre-Glued Super Patch Kit GSC-1 GearClean Brush MLP-1.2 Master Link Pliers PW-5 Pedal Wrench SD-2 Shop Screwdriver: #2 Phillips SW-7.2 Triple Spoke Wrench TL-1.2 Tire Lever Set #1622 Torx Compatible "L" Wrench
Park Tool MTC-10 Multi-Tool
$16.95
The MTC-10 features a super strong, composite, multi-position handle, with hardened and plated tools and smooth ergonomic operation. Lightweight, compact, and perfect to carry along. - 3, 4, 5 and 8mm hex wrenches - T25 Torx compatible driver - Combo cross/straight tip screwdriver - Key ring holder - Weight: 60g (2.12 ounces)
Park Tool MTC-20 Multi-Tool
$22.95
The MTC-20 features a super strong, composite, multi-position handle, with hardened and plated tools and smooth ergonomic operation. Lightweight, compact, and perfect to carry along. - 3, 4, 5 and 8mm hex wrenches - T25 Torx compatible driver - Combo cross/straight tip screwdriver - CO2 cartridge inflator adaptor - Key ring holder - Weight: 74g (2.61 ounces)
Park Tool Replacement Chain Tool Pin (2-Pack)
$9.82
Park Tool's Replacement Chain Tool Pin fits Park Tool's CT-6, CT-6.2, and CT-6.3 Chain Tools (each sold separately). • Made from hardened alloy tool steel • NOTE: The 985-1 will also push out the chain rivet completely from the chain side plate.
Park Tool SR-12.2 Sprocket Remover / Chain Whip
$33.99
Updated to fit current 12-speed cassettes, this combination chain whip and freewheel / lockring remover wrench is heat treated to prevent bending, flexing and wear and features a long, molded handle in addition to a built in hex shaped driver. - Works on 5- to 12-speed road and mountain bike cassettes and freewheels - 1-inch (25.4mm) box-end wrench fits Park Tool Freewheel / Cassette Lockring Tools - Features hardened pins to keep the chain in place
Park Tool Shop Cone Wrench
$8.49
Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.
Park Tool Sprocket Remover / Chain Whip
$29.99 - $31.00
This combination chain whip and freewheel / lockring remover wrench is heat treated to prevent bending and flexing, with a molded handle for comfort. - 3/32-inch model Works on 5- to 12-speed cassettes and freewheels - 1/8-inch model works on 1/8-inch chains and sprockets - 1-inch (25.4mm) box-end wrench fits Park Tool Freewheel/Cassette Lockring Tools - Features hardened pins to keep the chain in place
Park Tool Triple Spoke Wrench
$9.99
• Updated to fit better in the hand with a more rounded, smoother shape • The precision sized SW-7.2 fits the three most popular spoke nipple sizes on the market • Nickel plated for years of service • Designed for the home mechanic. FIts the following size spoke nipples: • .127" (3.23mm) • .130" (3.30mm) • .136" (3.45mm)
Park Tool Valve Core Tool
$10.99
Park's Valve Core Tool is great for tightening, removing and installing Schrader and Presta valve cores (the cores are inside the valve), and also Presta valve extenders that have 5mm wrench flats. It's a handy tool to save a tube when all that's wrong is a broken valve, and it also lets you remove valves to easily insert sealant.
Park Tool 1.3mm External Snap Ring Pliers
$20.95
Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-3 has 1.3mm tips on bent nose blades for medium, external snap rings.
Park Tool 1.3mm Internal Snap Ring Pliers
$20.95
Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-2 has 1.3mm tips on bent nose blades for medium, internal snap rings. The tips of the RP-2 open from 22mm down to 2mm (center to center).
Park Tool 1.7mm Snap Ring Pliers
$23.95
Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-4 has 1.7mm tips on bent nose blades for larger, internal snap rings. The tips open from 21mm down to 2mm (center to center).
Park Tool Adjustable Axle Set - For DT-5
$189.95
Upgrades the DT-5 to the DT-5.2. - Four telescoping axle adaptors - Two stand off studs for Flat Mount alignment - 12mm front fork thru axle sleeve
Park Tool BB86/92 Shell Pilot
$13.66
- Used when facing BB86/92 bottom bracket shells and reaming is not required - Used in conjunction with HTR-1 head tube reaming and facing set (PK-6710), 750.2 centering cone adapter (PK-6735) and 690-XL facing cutter (PK-6730)
Park Tool BBT-69.2 Bottom Bracket Tool
$27.99
Precision CNC machined aluminum tool for the installation and removal of 16-notch external bearing bottom brackets. Featuring updated tooth profiles to optimize the fit between the tool and high performance BB parts. Anodized and laser engraved for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. - 16 notch 44mm OD cups - Fits Shimano BB80, BB5700, XT BB70, BB51, and previous external bearing threaded cups - Also fits many external threaded types for Campagnolo, Chris King, FSA MegaExo, Hope, SRAM/Truvativ GXP, Race Face X-type, Surly, Wheels, Fulcrum, and others - Fits 16 notch rotor disc lockrings
Park Tool Belt Drive Tension Gauge
$56.95
The BDT-2 is a go/no-go style gauge designed to help set the proper tension on most belt drive systems and sizes. Also gauges rear cog parallelism and angularity.
Park Tool Bladed Spoke Holder
$8.95
Park's Bladed Spoke Holder is a must for building and truing wheels that feature bladed spokes. It has 4 different size slots to fit a wide variety of bladed (aero) spokes from .08 to 2mm wide. It holds them safely in place to prevent twisting as you turn the nipple to true and tension the wheel.
Park Tool Bottom Bracket Bearing Tool Set
$40.95
The BBT-30.4 Bottom Bracket Bearing Tool Set is designed and built to install and remove the bearings used in BB30, PressFit 30 (PF30), 386EVO, BBright and PF121 bottom bracket systems. The BBT-30.4 features a bushing set used in conjunction with a head cup press to quickly and precisely press the BB30 and PF30 bearings in the bottom bracket shell. The included BB30 bearing remover works from inside the shell to easily push out bearings.
Page 1 of 5 Next page